| The Model
AC1382 optional 10-foot cable is required to connect
a 25-pin RS-232C serial port from a host processor to a 6BP01-2,
6BP04-2, 6BP04HV-2 or 6BP16-2 backplane or
a 6B50-2 board.
The RS-232C connector is a female 25-pin DB-25. The 6BPXX-2
backplanes and the 6B50-2 digital board connector are male
25-pin DB-25. Only pins 1, 2, 3 and 7 (connected one-to-one)
are connected. |
Order
Now Model AC1382 |
| The Model AC1385 is
identical to the AC1382 cable except for a 9-pin female DB-9
connector that connects to 9-pin serial ports. Pins 2, 3 and
5 on the DB-9 connector are connected to pins 3, 2 and 7, respectively
on the DB-25 connector. |
Order
Now Model AC1385 |
| The Model CAB-03 3-foot
flat ribbon cable connects the 6B50-1
or 6B50-2 TTL-level discrete I/O channels to the DB-16
solid state relay backplanes. |
Order
Now Model CAB-03 |
|
back to top
|
CJC Temperature Sensor
|
The Model AC1361 temperature sensor provides
cold junction temperature measurement for thermocouple
applications on user-designed backplanes or mounting boards.
These SIP temperature sensors are included on each channel
of all 6B Series backplanes.
The minimum purchase quantity for the AC1361 is 50 pieces. |
Order
Now Model AC1361 |
|
back to top
|
Current Conversion Resistor
The Model
AC1381 is an encapsulated, plug-in, 50  ,
0.1%, 1/8 watt, 10 ppm/°C resistor that converts current
to voltage. The AC1381 can be mounted directly on the 6B
Series backplanes and
is required for each 4-20 mA or 0-20 mA input channel. |
Order
Now Model AC1381 |
|
back to top
|
Mounting Kit - Rack Mount
| The Model AC1380 optional
rack-mount kit fits any 6B Series backplane into
a 19-inch rack, requiring 19-inch x 3.5-inch area. The bottom
plate has threaded inserts for mounting each of the three backplanes
using four screws, and pre-drilled holes for attachment of
an AC/DC power supply (PWR-01). Mounting hardware is provided
with the AC1380. |
Order
Now Model AC1380 |
|
back to top
|
Configuration Jumpers
| Model AC1344 is
a spare set of 10 configuration jumpers (W1) for the 6B Series backplanes and 6B50 Digital
I/O boards. A configuration jumper is used to establish or
change the address, baud rate and checksum of any module when
inserted in any backplane first socket. A configuration jumper
is used to establish or change the address of any 6B50 board. |
Model AC1344 |
|
back to top
|
Power Supplies
| The Models PWR-01 AC/DC modular power
supply provides a +5 V DC regulated output. Model PWR-01
offers a +5 V DC @ 5 ampere output (25 watts). Model PWR-01
accepts a wide input range of 85 V AC to 280 V AC. |
Order
Now Model PWR-01 |
| After connecting a power cord,
no additional external components are required with this power
supply. Simply mount the unit on the backplane and connect
power. For the AC/DC supplies, connect Model AC1340-D power
cord to the AC POWER terminals, TB33. |
Order
Now Model AC1340-D |
|
back to top
|
User Manual and Configuration Software
| The optional Model AC1383 complete
reference manual provides detailed information on setting up
the 6B Series Subsystem. The manual includes complete specifications
and the 6B Series Command Set. An included utility/demo software
on a 3.5-inch software diskette enables a user to configure,
calibrate, read data from or write data to the 6B Series modules
and 6B50 I/O boards, without writing his own application programs.
The 6B Series User Manual with software diskette must be ordered
as a separate item. |
Order
Now Models AC1383 |
|
|
Ph: 1.248.615.4441
