| Board Format |
CoreExpress® 58 mm x 65 mm |
| Processor/Speed |
Intel Atom Type Z530 @ 1,6 GHZ or
Intel Atom Type Z510 @ 1,1 GHz
45 nm process
512K L2 cache
533 MT/s FSB
USFF uFCBGA8, 13x14mm, 0.6mm pitch, 447 pins |
| Core logic |
Intel System Controller Hub (SCH)
Type US15W
65 nm process
USFF uFCBGA3, 22x22mm, 0.6mm pitch, 1249 pins |
| RAM |
512 MB or 1 GB SDDR2, 533 MHz
Soldered on board |
| PCI Express |
2 root ports Spec. Rev. 1.0a (2 lanes x 1)
• Each port supports 2.5 Gb/s bandwith
in each direction
• Low power “L-states” are supported
• Hot-plug is supported
• External x1 graphics devices are supported
(internal GD must be disabled)
• Only SDVO or external graphics can be
used at one time |
| HD Audio |
High Definition Audio Controller supports
4 audio streams; 2 in, 2 out
• 1.8 V and 3.3 V I/O is supported
• Docking is supported
• Each stream can obtain up to 16 channels |
| SDIO/MMC |
Integrated Secure Digital I/O (SDIO) or Multimedia Card (MMC) Controller
Supports SDIO Rev. 1.1 and MMC Rev. 4.0. SDIO/MMC interface permits x1 and x4 I/O read/write modes,
SDHC supported |
| SMBus |
Compatible with most I2C devices and SMBus Spec. 1.0 for system management.
2 MByte serial EEPROM on board |
| GMBus/DDC |
I2C for display control |
| LPC |
Supports LPC 1.1 spec |
|
| Graphics |
Integrated graphics device (IGD) includes LVDS and SDVO display ports for simultan-eous independent operation of 2 displays.
• LVDS interface supports pixel color depth
of 18 and 24 bits,
• Max. pixel clock 112 MHz
(equates to 1376x768 @85 Hz)
• SDVO max. pixel clock 160 MHz
(equates to 1280x1024 @85 Hz)
• SDVO for any external device HDMI/DVI,
Analog, VGA/CRT, LVDS
Full hardware acceleration for:
• H.264 baseline profile L3, main profile 4.1
and high profile L4.1
• MPEG2 main profile high level
• MPEG4 simple profile L3, advanced
simple profile L5
• VC1 all profiles up to L3
• WMV9 simple profile medium level
• WMV9 main profile high level
• SD/HD TV broadcast up to 1080i |
| USB |
• USB 1.1 with 3 UHCI controllers,
• 2 USB 1.1 ports per controller (port 0-5)
• USB 2.2 with 1 EHCI controller with 8 ports,
ports 6 & 7 must be internal only to meet
USB spec requirements
• Debug port lives on Port 0
Port 2 can be USB client port,
USB On-The-Go is not supported
USB client connect signal
(USBCC/GPIOSUS3) may be used to
detect host/client connection |
| PATA (IDE) |
1 port supports 2 devices (master/slave)
with the following modes :
• PIO Modes 0, 1, 2, 3, 4
• Single-word DMA Modes 0, 1, 2
• Multi-word DMA Modes 0, 1, 2
• Ultra-DMA Modes 0, 1, 2, 3, 4, 5
• Up to 100 MBytes/s in UDMA-100 mode |
Operating
temperature |
-20 °C … +60 °C
-40 °C … +85 °C (optional) |
| Power Supply |
+5 V +/- 5 %, ~5 Watts |
| BIOS |
Award BIOS
1 MByte firmware hub (FWH) |
|
Ph: 1.248.615.4441
